Category: pyrrolines

541-59-3, Maleimide is a pyrrolines compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,541-59-3

The title compound was prepared using a modification of the method of Foley, et al., 2010 Biomol. Chem. 8:4601-4606). To a solution of maleimide (5.0 g, 51.5 mmole) in dry ethyl acetate (250 mL) was added N-methylmorpholine (5.7 mL, 51.5 mmole) and this mixture cooled to 0 C. (ice-bath) under anhydrous N2(g). Methyl chloroformate (4.8 mL, 61.8 mmole) was added slowly with stirring under anhydrous conditions, and the reaction allowed to stir at 0 C. for 30 min. and at room temperature for 30 min. The reaction mixture was filtered through a Buchner funnel and the white precipitate washed with ethyl acetate (100 mL). The combined filtrate was extracted with ice-water (1*100 mL) and brine solution (1*100 mL) and then dried over anhydrous magnesium sulfate. The product was filtered and evaporated to a clear oil that was co-evaporated with dry toluene (2*25 mL) and dried in vacuo under high vacuum overnight. The resulting clear oil was crystallized by trituration from anhydrous diethylether (50 mL) to give an off-white solid (2.77 g, 35%) homogeneous by t.l.c. (irrigant=9:1 dichloromethane:methanol, Rf=0.62).

541-59-3 Maleimide 10935, apyrrolines compound, is more and more widely used in various.

Reference£º
Patent; Marker Gene Technologies, Inc.; Naleway, John Joseph; Harlan, Fiona Karen; Lusk, Jason Scott; (72 pag.)US2018/207287; (2018); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1122-10-7,3,4-Dibromo-1H-pyrrole-2,5-dione,as a common compound, the synthetic route is as follows.

General procedure: Dried pressure tube was charged with magnetic stir bar and50 mg of PdSiO2 catalysts (1 mol% with respect to amine). Then,1.0 mL o-xylene was added, followed by the addition of 0.5 mmolof amine and 1 mmol of benzyl alcohol. The pressure tube wasflushed with argon was closed with screw cap. Then it was placedin the preheated aluminum block and reaction was allowed to progressfor 30 h at 150 C. After completion of the reaction, pressuretube was removed from aluminum block and cooled down to roomtemperature. The catalyst was filtered out by ciliate and reactionproducts were analyzed by GC-MS and the corresponding amineswere purified by column chromatography. The yields of selectedamines were determined by GC analysis using n-hexadecane asstandard. For this purpose, after completion of the reaction, nhexadecane(100 mL) as standard was added to the reaction pressuretube and the reaction products were diluted with ethyl acetate followed by filtration using plug of silica and then subjected GCanalysis., 1122-10-7

1122-10-7 3,4-Dibromo-1H-pyrrole-2,5-dione 14279, apyrrolines compound, is more and more widely used in various.

Reference£º
Article; Alshammari, Ahmad S.; Natte, Kishore; Kalevaru, Narayana V.; Bagabas, Abdulaziz; Jagadeesh, Rajenahally V.; Journal of Catalysis; vol. 382; (2020); p. 141 – 149;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.25021-08-3,2-(2,5-Dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetic acid,as a common compound, the synthetic route is as follows.

Trifluoroacetic acid/L-alanyl-N5-carbamoyl-N-(4-{[(2,5-dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetyl]amino}phenyl)-L-ornithinamide (1:1) The title compound was prepared from 1,4-phenylenediamine sequentially according to classical methods of peptide chemistry. In the first step, 942 mg (8.72 mmol) of 1,4-phenylenediamine were monoacylated with 0.8 g (2.9 mmol) of N2-(tert-butoxycarbonyl)-N5-carbamoyl-L-ornithine in the presence of HATU and N,N-diisopropylethylamine. In the second step, in an analogous manner, the second anilinic amino group was acylated with (2,5-dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetic acid in the presence of HATU and N,N-diisopropylethylamine. Deprotection with TFA, coupling with 2,5-dioxopyrrolidin-1-yl N-(tert-butoxycarbonyl)-L-alaninate and another deprotection with TFA then gave, in 3 further synthesis steps, the title compound, 148 mg of which were obtained by this route. LC-MS (Method 1): Rt=0.21 min; MS (ESIpos): m/z=474 (M+H)+. LC-MS (Method 4): Rt=0.2 min; MS (ESIpos): m/z=474 (M+H)+.

25021-08-3, The synthetic route of 25021-08-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; BAYER PHARMA AKTIENGESELLSCHAFT; LERCHEN, Hans-Georg; REBSTOCK, Anne-Sophie; CANCHO GRANDE, Yolanda; WITTROCK, Sven; BERNDT, Sandra; GRITZAN, Uwe; FITTING, Jenny; STELTE-LUDWIG, Beatrix; JONES, Patrick; MAHLERT, Christoph; VOTSMEIER, Christian; SCHOeNFELD, Dorian; TRAUTWEIN, Mark; WEBER, Ernst; PAWLOWSKI, Nikolaus; GREVEN, Simone; GLUeCK, Julian Marius; HAMMER, Stefanie; DIETZ, Lisa; MAeRSCH, Stephan; (357 pag.)US2020/138970; (2020); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

134272-64-3, N-(2-Aminoethyl)maleimide Hydrochloride is a pyrrolines compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

To a suspension of the free thiol, Dl (88 mg, 0.105 mmol) and l-((2,5- dioxopyrrolidin-l-yl)oxy)-l-oxo-4-(pyridin-2-yldisulfanyl)butane-2-sulfonic acid (sulfo- SPDB) (64.0 mg, 0.158 mmol) in anhydrous dichloromethane (2.10 mL) was added DIPEA (55.0 mu, 0.315 mmol) under nitrogen at room temperature. The mixture stirred for 16 hours and then l-(2-aminoethyl)-lH-pyrrole-2,5-dione hydrochloride (55.6 mg, 0.315 mmol), anhydrous dichloromethane (1.0 mL) and DIPEA (0.055 mL, 0.315 mmol) were added. The mixture stirred for an additional 5 hours at room temperature upon which the reaction was concentrated in vacuo. The resulting residue was purified by RP-HPLC (CI 8, CH3CN/H2O). Fractions containing desired product were frozen and lyophilized to give maleimide, D4 (20 mg, 16% yield) as a white solid. LCMS = 4.92 min (8 min method). MS (m/z): 1158.6 (M + 1)+.

134272-64-3, The synthetic route of 134272-64-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; IMMUNOGEN, INC.; MACROGENICS, INC.; HICKS, Stuart William; YODER, Nicholas C.; BARAT, Bhaswati; BONVINI, Ezio; DIEDRICH, Gundo; JOHNSON, Leslie S.; LOO, Deryk; SCRIBNER, Juniper A.; (260 pag.)WO2018/119196; (2018); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.151038-94-7,6-(2,5-Dioxo-2,5-dihydro-1H-pyrrol-1-yl)hexanehydrazide 2,2,2-trifluoroacetate,as a common compound, the synthetic route is as follows.

EMCH-TFA (3 equiv) and 0.75 equiv TFA were added to an anhydrous ethanol (dried by 3 A molecular sieves, superactivated by heating to 150 C under a vacuum of 0.1 Torr) solution (8.57 mL) of PPD (15 mg, 18.3 muiotaetaomicron, 1 equiv) and stirred under a nitrogen atmosphere overnight at room temperature. The extent of the reaction was monitored by HPLC (Method 1.3). Once 90% complete by HPLC, the solution was evaporated to dryness and the residue redissolved in anhydrous DMSO. PPD/PPD-EMCH was precipitated by adding at least 3 volumes of PBS (pH 7.4). The precipitate was washed with dH20 (pH > 6.5) and redissolved in DMSO. The precipitation was repeated three times, followed by further purification by radial chromatography, eluting PPD and PPD-EMCH with 90: 1 and 20: 1 chloroform:methanol, repectively. NMR spectra were obtained at 56C in deuteriochloroform (Figure 5)., 151038-94-7

The synthetic route of 151038-94-7 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; THE REGENTS OF THE UNIVERSITY OF COLORADO, A BODY CORPORATE; KOCH, Tad, H.; BARTHEL, Benjamin, L.; ROWAN, Alexander, R.H.; WO2012/167255; (2012); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1334177-86-4,1-(2,5-Dioxo-2,5-dihydro-1H-pyrrol-1-yl)-3-oxo-7,10,13,16,19,22,25,28-octaoxa-4-azahentriacontan-31-oic acid,as a common compound, the synthetic route is as follows.

(d) 1-(3-(2, 5-dioxo-2 , 5-dihydro- 1H-pyrrol- 1-yl)propanamido)-N-((S)- 1-(((S)- 1-((4-((S)-7- methoxy-8-((5-(((S)- 7-methoxy-2-(4-(4-methylpiperazin- 1-yl)phenyl)-5-oxo-5, 1 la-dihydro- 1H- benzo[e]pyrrolo[1, 2-a][1, 4]diazepin-8-yl) oxy)pentyl) oxy)-5-oxo-5, 1 la-dihydro- 1H- benzo[e]pyrrolo[1, 2-a][1, 4]diazepin-2-yl)phenyl)amino) – 1-oxopropan-2-yl)amino)-3-methyl- 1- oxobutan-2-yl)-3, 6,9, 12,15, 18,21, 24-octaoxaheptacosan-2 7-amide (91)Piperidine (0.2 mL) was added to a solution of 90 (77 mg, 63.4 pmol) in DMF (1 mL). The reaction mixture was allowed to stir for 20 minutes. The reaction mixture was carefully diluted with DCM (50 mL) and washed with water (50 mL). The organic layers was washed with brine (100 mL), dried over Mg504, filtered and evaporated under reduced pressure to provide the unprotected valine intermediate. The crude residue was immediately redissolved in chloroform (5 mL). Mal(Peg)8-acid (56 mg, 95 pmol) and EDCI (18 mg, 95 pmol) were added, followed by methanol (0.1 mL). The reaction was allowed to stir for 3 hours at room temperature at which point completion was observed by TLC and LC/MS (1.19 mm (ES+) m/z(relative intensity) 784.25 (([M+ 2H]2j/2, 100)). The reaction mixture was diluted with chloroform (50 mL), washed with water (100 mL), dried (MgSO4), filtered and evaporated in vacuo, followed by high vacuum drying, to provide the crude product. Purification by flash chromatography (gradient elution: HPLC grade 96:4 v/v CHCI3/MeOH to 90:10 v/v CHCI3/MeOH) gave 91 as a yellow solid (43 mg, 43%). 1H NMR (400 MHz, ODd3) O 8.73 (5, 1H), 7.88 (dd, J= 7.6, 3.9 Hz, 2H), 7.75 (d, J= 8.6 Hz, 2H), 7.52 (d, J= 2.0 Hz, 2H), 7.44 (5, 1H), 7.40-7.28 (m, 4H), 6.91 (d, J= 8.8 Hz, 2H), 6.81 (5, 2H), 6.69 (5, 2H),6.48 (5, 1 H), 4.72 -4.63 (m, 1 H), 4.46 -4.34 (m, 2H), 4.25 – 4.03 (m, 6H), 3.95 (5, 4H), 3.84 (dd, J = 17.2, 10.1 Hz, 4H), 3.72 -3.46 (m, 30H), 3.44 -3.32 (m, 4H), 3.30-3.20 (m, 4H), 2.75-2.63 (m, 1H), 2.59 (5, 4H), 2.55-2.43 (m, 3H), 2.37 (5, 3H), 2.29 (dd, J= 12.7, 6.7 Hz, 1H), 2.03-1.89 (m, 4H), 1.72 (d, J= 22.7 Hz, 8H), 1.46 (d, J= 7.2 Hz, 3H), 1.01 (dd, J = 11.5, 6.9 Hz, 6H). MS (ES) m/z (relative intensity) 784.25 (([M+ 2H]2)/2, 100).

1334177-86-4, As the paragraph descriping shows that 1334177-86-4 is playing an increasingly important role.

Reference£º
Patent; CANCER RESEARCH TECHNOLOGY LIMITED; VAN BERKEL, Patricius Henrikus Cornelis; HOWARD, Philip Wilson; WILLIAMS, David G; WO2015/159076; (2015); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

69778-83-2, 4-Methoxy-1H-pyrrol-2(5H)-one is a pyrrolines compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,69778-83-2

A. A mixture of 4-methoxy-3-pyrrolin-2-one (3 g), 1-octanol (7.4 ml) and methanesulfonic acid (0.2 g) were heated at 100¡ã C. for 2 hours under reduced pressure (40 mbars). The product was chromatographed on silica gel, eluding with 2percent methanol in methylene chloride, to give 4-octyloxy-3-pyrrolin-2-one.

The synthetic route of 69778-83-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Researche Syntex France, S.A.; US4997846; (1991); A;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.25021-08-3,2-(2,5-Dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetic acid,as a common compound, the synthetic route is as follows.,25021-08-3

250 mg (1.07 mmol) of tert-butyl 3-[2-(2-aminoethoxy)ethoxy]propanoate, 151 mg (0.974 mmol) of 2-(2,5-dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetic acid, 224 mg (1.46 mmol) of 1-hydroxy-1H-benzotriazole hydrate and 224 mg (1.17 mmol) of 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride were dissolved in 5.0 ml of dimethylformamide. The reaction mixture was stirred at RT for 1 h. Ethyl acetate was added and the mixture was extracted twice with 5% strength citric acid solution and with saturated sodium bicarbonate solution. The organic phase was washed twice with saturated sodium chloride solution and dried over magnesium sulphate, and the solvent was evaporated under reduced pressure. The residue was purified by preparative RP-HPLC (column: Reprosil 250*40; 10mu, flow rate: 50 ml/min, MeCN/water/0.1% TFA). The solvents were evaporated under reduced pressure and the residue was dried under high vacuum. This gave 267 mg (64% of theory) of tert-butyl 3-[2-(2-{[(2,5-dioxo-2,5-dihydro-1H-pyrrol-1-yl)acetyl]amino}ethoxy)ethoxy]propanoate. LC-MS (Method 1): Rt=0.73 min; MS (ESIpos): m/z=371 (M+H)+.

The synthetic route of 25021-08-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Bayer Pharma Aktiengesellschaft; LERCHEN, Hans-Georg; REBSTOCK, Anne-Sophie; CANCHO GRANDE, Yolanda; MARX, Leo; STELTE-LUDWIG, Beatrix; TERJUNG, Carsten; MAHLERT, Christoph; GREVEN, Simone; SOMMER, Anette; BERNDT, Sandra; (684 pag.)US2018/169256; (2018); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

17057-04-4, 4-(2,5-Dioxo-2,5-dihydro-pyrrol-1-yl)-benzoicacid is a pyrrolines compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,17057-04-4

General procedure: Equimolar quantities of maleimide (2) and nitrones (5a-k and 6a-k) were refluxed in toluene (20 ml) and ethyl alcohol (5 ml) for 8-10 h (TLC monitoring using petroleum ether and hexane 1:1) followed by cooling with addition of dry ether. The products (7a-k and 8a-k) were separated out after filtration and recrystallized from toluene and petroleum ether mixture (1:1) to yield cis-isomers (7aa-7ka and 8aa-8ka). The mother liquor on further work up provided trans-isomers which were recrystallized from ethanol and diethyl ether mixture (1:1) (7aa’-7ka’ and 8aa’-8ka’) (Fig. 3).7 These stereoisomers were characterized by their 1H NMR, IR and mass spectra in addition to their melting points and elementary analysis. These stereoisomers have identical IR spectra and elemental analysis but differ in their melting points, 1H NMR and mass spectra.

The synthetic route of 17057-04-4 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Anand, Preet; Singh, Baldev; Bioorganic and Medicinal Chemistry; vol. 20; 1; (2012); p. 521 – 530;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.73286-71-2,N-Boc-2-pyrroline,as a common compound, the synthetic route is as follows.,73286-71-2

tert-butyl-(3-trimethylsilylethynyl)-3a,4, 5,6a-tetrahydropyrrolo[3,2-d]isoxazole-6-carboxylate (Intermediate 20b, alternative procedure) A solution of tert-butyl 2,3-dihydropyrrole-1-carboxylate (500 mg, 2.95 mmol) and 3-trimethylsilylprop-2-ynal oxime (459.06 mg, 3.25 mmol) in MTBE (15 mL) was cooled to 0-5 C. while stirring. Sodium hypochlorite (2.806 mL, 5.91 mmol) was added dropwise keeping the reaction temperature below 20 C. The reaction mixture was stirred at the same temperature for 3 hours; afterwards, it was quenched with Na2SO3 solution; the two phases were separated, the organic layer was washed with water and brine, dried over Na2SO4, filtered and evaporated to dryness in vacuo. The crude residue was purified by automated flash chromatography (Biotage SP1, cartridge type SNAP25) using a gradient from petroleum ether:EtOAc 95:5 to 7:3.

As the paragraph descriping shows that 73286-71-2 is playing an increasingly important role.

Reference£º
Patent; Recordati Ireland Ltd.; Riva, Carlo; De Toma, Carlo; Angelico, Patrizia; Poggesi, Elena; Graziani, Davide; (36 pag.)US2016/185798; (2016); A1;,
Pyrroline – Wikipedia
1-Pyrroline | C4H7N – PubChem